Details:-
- 3-axis magnetic electronic compass.
- Precise heading information.
- Operating Voltage: 3 -5 V DC.
- Driver Chip: HMC5883L.
- Communication: I2C protocol.
- Measuring range: ± 1.3-8 Gauss.
MPU-6050 3-Axis Accelerometer and Gyro Sensor
Details:-
- Chip built-in 16bit AD converter, 16-bit data output
- Driver Chip: MPU6050
- Operating Voltage: 3-5V DC
- Communication: I2C/IIC Protocol
- Gyro Range: ± 250, 500, 1000, 2000 °/s
- Accelerometer Range: ± 2 ± 4 ± 8 ± 16 g
Force Sensitive Resistor Square
This is a force sensitive resistor with a square, 1.75 x 1.5″, sensing area. This FSR will vary its resistance depending on how much pressure is being applied to the
MLX90614 Non-Contact Infrared Temperature Sensor GY-906
MLX90614 is an infrared thermometer designed for non-contact temperature sensing. An internal 17-bit ADC and a powerful DSP contribute to the MLX90614’s high accuracy and resolution. It has a huge
SW-420 Vibration Sensor Module
Details:-
- Using SW-420 normally closed type vibration sensor
- Comparator output, clean signal, good waveform, strong driving ability, >15mA
- Operating voltage 3.3V ~ 5V
- Output format: digital switching output (0 and 1)
- Using a wide voltage LM393 comparator
- With bolt holes for easy installation
Micro Load Cell (Weight Sensor) with 3kg Capacity
This Load cell can be used to measure the weight of objects between 0 and 3kg. This straight bar load cell (sometimes called a strain gauge) can translate up to
HW-006 V1.3 Line Tracker Sensor Module
The infrared emitting diode of the TCRT5000 sensor continuously emits infrared rays. When the emitted infrared rays are not reflected back or reflected back but the intensity is not strong
MQ4 – Methane (CNG) Natural Gas Sensor Module
MQ4 Methane CNG Gas Sensor Module can sense the presence of Compressed Natural Gas(CNG), methane(CH4), etc. in the air. The module uses our MQ-4 sensor. It simplifies the interface to
Ceramic Piezoelectric Vibration Sensor Module
This analog piezoelectric ceramic vibration module buffers a piezoelectric transducer, which responds to strain changes by generating a measurable output voltage change proportional to the strength of vibration, also known
MQ 135 Air Quality/Gas Detector Sensor Module For Arduino
Details:-
- Sensitivity to Ammonia, Sulphide and Benzene steam
- Sensitive for benzene, alcohol, smoke
- Fast response and recovery
- Adjustable sensitivity
- Signal output indicator
- Output voltage boosts along with the concentration of the measured gases increases.
Normally open vibration sensor module
Details:-
- The working voltage of 3.3V-5V.
- Using the company’s high-sensitivity vibration switch, the default with SW-18015P vibration sensor.
- The comparator output, the signal clean, good waveform, driving ability, more than 15mA
- With a fixed bolt hole, easy to install.
- The use of wide voltage LM393 comparator.
Flame sensor Module
Details:-
- Comparator chip LM393 makes module readings stable.
- Operating voltage 3.3V-5V.
- Fast Response Time
- Sensitivity adjustable
- Detects a flame or a light source of a wavelength in the range of 760nm-1100 nm.
- Detection range: up to 100 cm.
- Adjustable detection range.
- Detection angle about 60 degrees, it is sensitive to the flame spectrum.
MQ-3 Alcohol Detector Gas Sensor Module
Details:-
- Power requirements: 5 VDC @ ~165 mA (heater on) / ~60 mA (heater off).
- Current Consumption: 150mA.
- DO output: 0.1 and 5V.
- AO output: 0.1- 0.3 V (relative to pollution), the maximum concentration of a voltage of about 4V
- Detecting Concentration: 0.05-10mg/L Alcohol.
MQ2 Smoke Sensor Module
Details:-
- Operating Voltage is +5V
- Can be used to Measure or detect LPG, Alcohol, Propane, Hydrogen, CO, and even methane
- Can be used as a digital or analog sensor
- Long life and low cost
- Simple drive circuit
MQ7 – Carbon Monoxide Gas Sensor Module
Details:-
- Operating voltage: DC 5 V.
- The analog output voltage, the higher the concentration the higher the voltage.
- The carbon monoxide detection with better sensitivity.
- With a long service life and reliable stability.
- Rapid response and recovery characteristics.
- Range: 10 to 1000 ppm.
WeMos D1 Mini Development board
- 11 digital input/output pins
- Interrupt/PWM/I2C/one-wire
- 1 analog input(3.2V max input)
- 16M bytes(128M bit) Flash
- External antenna connector
- Built-in ceramic antenna
- New CP2104 USB-TO-UART IC
Original Arduino Due Board
- A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
- CPU clock at 84Mhz
- 96KBytes of SRAM
- 512KBytes of flash memory for code
- A DMA controller, that can relieve the CPU from doing memory intensive tasks.
STM32F103CBT6 Maple Mini
- 100% Brand new and high quality STM32 Board
- Model: STM32F103CBT6
- Core: ARM 32 Cortex-M3 CPU.
- 72MHz work frequency.
- 128K flash memory, 20K SRAM.
- 2.0-3.6V power, I/O.
Original Arduino Mega 2560 R3 Board
Details:-
- 54 Digital I/O terminals (14 of which have programmable PWM outputs).
- 16 Analog Inputs.
- 4 UARTs (hardware serial ports).
- 16 MHz crystal clock.
- Operating voltage: 6 ~ 12v.
- Dimensions: 110 x 53 x 15 mm.
Original Arduino Uno Rev3
Details:-
- Arduino Uno REV 3 is an Arduino board based on the microcontroller ATmega328P.
- It comes with 14 digital I/O pins out of which 6 can be used as PWM outputs.
- There are 6 analog input pins and the board’s clock frequency is 16MHz which is used for the synchronization of internal functions.
- Moreover, this board includes a power jack, USB connection, ICSP header, and reset button.
- In fact, it contains almost everything required to support the built-in controller. Simply plug this device with the computer using a USB cable or power it up with an AC-to-DC adopter or battery and start playing with it.
- The operating voltage is 5V while the input voltage ranges from 6 to 20 and the recommended input voltage ranges from 7 to 12V.
