Smartiphi catalog
Shop electronics components by project need
Browse development boards, DIY kits, sensors, modules, robotics parts, displays, tools and power supplies for learning, lab and prototype work.
Shop
Showing 261–280 of 386 results
-
Arduino, Boards, Development Boards
Original Arduino Due Board
- A 32-bit core, that allows operations on 4 bytes wide data within a single CPU clock.
- CPU clock at 84Mhz
- 96KBytes of SRAM
- 512KBytes of flash memory for code
- A DMA controller, that can relieve the CPU from doing memory intensive tasks.
SKU: n/a -
-
Arduino, Boards, Development Boards, Others, Programmers
Original Arduino Micro
Details:-
- Manufacturer: Arduino Officials
- Support TWI and SPI communication
- Input voltage (recommended) range from 7V to 12V
- Input Voltage (limit) range from 6V to 20V
- 20 digital input/output pins (of which 7 can be used as PWM outputs and 12 as analog inputs)
- Onboard ATmega32u4 microcontroller with 32KB flash memory, 2.5KB SRAM and 1KB EEPROM
SKU: n/a -
-
Arduino, Boards, Development Boards
Original Arduino Nano
Details:-
- Manufacturer: Arduino Officials
- Operating Voltage (logic level): 5V
- 8 analog inputs ports: A0 ~ A7
- 14 Digital input / output ports: TX, RX, D2 ~ D13
- 1 pair of TTL level serial transceiver ports RX / TX
- Using Atmel Atmega328P-AU MCU
- There is a bootloader installed in it
- Standard 0.1” spacing DIP (breadboard friendly).
- Manual reset switch.
SKU: n/a -
Arduino, Boards, Development Boards
Original Arduino Uno Rev3
Details:-
- Arduino Uno REV 3 is an Arduino board based on the microcontroller ATmega328P.
- It comes with 14 digital I/O pins out of which 6 can be used as PWM outputs.
- There are 6 analog input pins and the board’s clock frequency is 16MHz which is used for the synchronization of internal functions.
- Moreover, this board includes a power jack, USB connection, ICSP header, and reset button.
- In fact, it contains almost everything required to support the built-in controller. Simply plug this device with the computer using a USB cable or power it up with an AC-to-DC adopter or battery and start playing with it.
- The operating voltage is 5V while the input voltage ranges from 6 to 20 and the recommended input voltage ranges from 7 to 12V.
SKU: n/a -
Arduino, Boards, Development BoardsDeal
Original: Arduino UNO R3 DIP Development Board with ATmega328a
-6%
Arduino, Boards, Development BoardsOriginal: Arduino UNO R3 DIP Development Board with ATmega328a
Details:-
- Micro-controller : Arduino Uno R3 ATmega328.
- Operating Voltage : 5V.
- Input Voltage (recommended) : 7-12V.
- Digital I/O Pins : 14 (of which 6 provide PWM output).
- Analog Input Pins : 6.
SKU: n/a -
Audio Modules, Modules
PAM8403 with Output Controlling Potentiometer
Details:-
- Operating voltage: 2.5V-5.5V
- Maximum output power: 3W x 2
- PCB size is about: length 30mm width 22mm overall height after installed is about 16mm
- Built with switch Potentiometer, can adjust the volume & control power switch freely!
- Flexible assembly usage.
SKU: n/a -
-
Modules & Sensors, Relays
Photosensitive Resistance Sensor Relay Module
Details:-
- Adjust the sensitivity with the potentiometer. Set the start relay threshold by adjusting the potentiometer.
- When it is brighter, the module relay pulls in.
- When the threshold is dark, the relay is disconnected.
- Operating Voltage: 3.3V – 5V.
SKU: n/a -
-
Gas and Dust Sensors, Modules & Sensors, SensorsDealStock check
PM2.5 GP2Y1010AU0F Optical Dust Sensor
-5%
Gas and Dust Sensors, Modules & Sensors, SensorsPM2.5 GP2Y1010AU0F Optical Dust Sensor
Details:
- Power supply voltage: DC5 ± 2V
- Sensitivity: 0.5V / (0.1mg / m3)
- The minimum detection level of particles: 0.8 m
- Clean air voltage: 0.9V typ.
- Low consumption current (Icc: MAX. 20 mA)
- The presence of dust can be detected by the photometry of only one pulse
- Enable to distinguish smoke from house dust
SKU: n/a
